Startseite Produkte OLED-Anzeige Grafik-OLED-Anzeigen WEO012832G

1,71 Zoll COG OLED-Modul

Modellnummer WEO012832G

►1,71" OLED
►Typ: Grafik
►Bauweise: COG
►128 x 32 Punktmatrix
►Integrierter Controller SSD1307ZD
►3-V-Stromversorgung
►1/32 duty
►Schnittstelle: SPI, I2C

Beschreibung

Das WEO012832G ist ein 1,71 Zoll Passivmatrix-OLED Modul, das aus 128x32 Punkten besteht. Es ist mit dem IC SSD1307 ausgestattet, das die I2C und 4-Draht-SPI Schnittstelle, 3V-Spannungsversorgung und 1/32 duty rate unterstützt.

Das WEO012832G ist ein OLED mit COG-Struktur, das extrem dünn ist und keine Hintergrundbeleuchtung benötigt. Es ist leicht und sparsam im Energieverbrauch. Dieses Modul eignet sich für Smart-Home-Anwendungen, tragbare Geräte, Gesundheits- und Testgeräte, usw. Es ist in der Farbe Weiss erhältlich; die anderen Farben werden auch in Kürze verfügbar sein. Das WEO012832G Modul kann bei Temperaturen von -40 ℃ bis + 80 ℃ betrieben werden; die Lagertemperatur liegt zwischen -40°C und +85°C.

  • WEO012832GW : Weiß
  • WEO012832GO : Orange (might have MOQ)

 

Zeichnung

Technische Daten

Schnittstelle Pin-Funktion

No. Symbol Beschreibung
1 N.C. (GND) Reserved Pin (Supporting Pin)
The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.
2 VCC Power Supply for OEL Panel
This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used.
3 VLSS Ground of Analog Circuit
This is an analog ground pin. It should be connected to VSS externally.
4 VSS Ground of Logic Circuit
This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground.
5 VDD Power Supply for Logic
This is a voltage supply pin. It must be connected to external source.
6 CS# Chip Select
This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low.
7 RES# Power Reset for Controller and Driver
This pin is reset signal input. When the pin is low, initialization of the chip is executed.
8 D/C# Data/Command Control
When the pin is pulled high and serial interface mode is selected, the data at SDIN is treated as data. When it is pulled low, the data at SDIN will be transferred to the command register. In I2C mode, this pin acts as SA0 for slave address selection.
9~11 D0~D2 Host Data Input/Output Bus
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
12 IREF Current Reference for Brightness Adjustment
This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 12.5μA.
13 VCOMH Voltage Output High Level for COM Signal
This pin is the input pin for the voltage output high level for COM signals.  A capacitor should be connected between this pin and VSS.
14 VCC Power Supply for OEL Panel
This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used.
15,16 BS0 Communicating Protocol Select
These pins are MCU interface selection input. See the following table:
  BS0 BS1
I2C 0 1
3-wire SPI 1 0
4-wire SPI 0 0
BS1
17 VLSS Ground of Analog Circuit
This is an analog ground pin. It should be connected to VSS externally.
18 N.C. (GND) Reserved Pin (Supporting Pin)
The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.

mechanische Daten

Artikel Ausmaß Einheit
Punktmatrix 128 × 32 Dots
Abmaße der modul 50,50 × 15,75 × 2,01 mm
Aktiver Bereich 42,22 × 10,54 mm
Pixelgröße 0,308 × 0,308 mm
Pixelabstand 0,33 × 0,33 mm
der Anzeigemodus Passive Matrix
die Farbe des Displays Monochrome (Weiß)
Drive Duty 1/32 Duty
IC SSD1307ZD
Schnittstelle SPI, I2C
Größe 1,71 Zoll

elektronische Eingenschaften

Artikel Symbol Bedingung Mindestwert typischer Wert Maximalwert Einheit
Supply Voltage for Logic VDD 2,8 3,0 3,3 V
Supply Voltage for Display VCC 11,5 12,0 12,5 V
High Level Input VIH 0,8×VDD V
Low Level Input VIL 0 0,2×VDD V
High Level Output VOH 0,9×VDD V
Low Level Output VOL 0,1×VDD V
Operating Current for VCC (Full ON) ICC VCC=12,0V 14,5 19,0 mA

absolute Grenzwerte

Parameter Symbol Mindestwert Maximalwert Einheit
Supply Voltage for Logic VDD -0,3 4,0 V
Supply Voltage for Display VCC 0 16,0 V
Betriebstemperatur TOP -40 +80 °C
Lagertemperatur TSTG -40 +85 °C
go top
close