Home Productos Pantalla OLED Pantalla OLED Gráfico WEO004864A

Módulos OLED Diodos Orgánicos 0.71 pulgada, 48x64 puntos, I2C

Modelo Nº WEO004864A

►Tipo: Gráfico
►Estructura: COG
►Tamaño : 0.71 pulgada
►Matriz de puntos 48 x 64
►Controlador integrado SSD1306BZ
►Fuente de alimentación de 3V
►1/64 duty
►Interfaz : I2C

DESCRIPCIÓN

  • WEO004864AW : Blanco
  • WEO004864AL : Amarillo
  • WEO004864AS : Azul cielo

DIBUJO

Winstar Display - 0.71" Graphic OLED 48x64, 0.71 oled

ESPECIFICACIONES

Función interfaz Pin

No. Símbolo Función
1 C2N Positive Terminal of the Flying Inverting Capacitorr Negative Terminal of the Flying Boost Capacitor The charge-pump capacitors are required between the terminals. They must be floated when the converter is not used.
2 C2P
3 C1P
4 C1N
5 VBAT Power Supply for DC/DC Converter Circuit
This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used.
6 NC No connection.
7 VSS Ground of Logic Circuit
This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground.
8 VDD Power Supply for Logic
This is a voltage supply pin. It must be connected to external source.
9 RES# Power Reset for Controller and Driver
This pin is reset signal input. When the pin is low, initialization of the chip is executed.
10 SCL Host Data Input/Output Bus
11 SDA When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. When I2C mode is selected, D2 & D1 should be tired together and serve as SDAout & SDAin in application and D0 is the serial clock input SCL.
12 IREF Current Reference for Brightness Adjustment
This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 12.5μA.
13 VCOMH Voltage Output High Level for COM Signal
This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS.
14 VCC Power Supply for OEL Panel
This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used.

Datos mecánicos

Elemento Dimensión Unidad
Matriz de puntos 48 × 64 Dots
Dimensión del módulo 13.90 × 22.0 × 1.26 mm
zona activa 10.54 × 14.70 mm
Tamaño del punto 0.198 × 0.208 mm
Distancia entre puntos 0.220 × 0.230 mm
Modo de visualización Matriz pasiva
Drive Duty 1/64 Duty
IC SSD1306BZ

Características electrónicas

Elemento Símbolo Condición Valor mín. Valor típico Valor máx. Unidad
Supply Voltage for Logic  VDD 2.8 3 3.3 V
Supply Voltage for Display  VCC 7 7.5 7.8 V
Input High Volt. VIH 0.8 xVDD VDDIO V
Input Low Volt. VIL 0 0.2 xVDD V
Output High Volt. VOH 0.9 xVDD VDDIO V
Output Low Volt. VOL 0 0.1 xVDD V
50% Check Board operating Current ICC VCC=7.5V 15 25 mA

Search keyword: 48x64 oled, oled 48x64, 0.71 oled, 0.71 " oled, 0.71 inch oled, oled 0.71 , oled 0.71 "
go top
close