Accueil Produits Module OLED Afficheur OLED graphique WEO012832D

Afficheur Portables 0.91 pouces, 128x32

N° de modèle WEO012832D

►Thinner version OLED
►Type: Graphique (sans cadre)
►Structure: COG
►Dimension: 0.91 pouces
►Suitable for wearable device
►Matrice de points 128 x 32
►Contrôleur intégré SSD1306BZ
►Alimentation 3V
►1/32 duty
►Interface: SPI
►2017 Taiwan Excellence Award

DESCRIPTION

  • WEO012832DWPP3N00008 : Blanc
  • WEO012832DLPP3N00004 : Jaune

 

DESSIN

OLED 128x32, 128x32 OLED Display, 0.91 inch OLED - WEO012832D

SPÉCIFICATIONS

Fonction PIN sur l'interface

No. Symbole Fonction
1 C2P Positive Terminal of the Flying Inverting CapacitorNegative Terminal of the Flying Boost CapacitorThe charge-pump capacitors are required between the terminals. They must be floated when the converter is not used.
2 C2N
3 C1P
4 C1N
5 VBAT Power Supply for DC/DC Converter Circuit
This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used.
6 VSS Ground of Logic Circuit
This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground.
7 VDD Power Supply for Logic
This is a voltage supply pin. It must be connected to external source.
8 CS# Chip Select
This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low.
9 RES# Power Reset for Controller and Driver
This pin is reset signal input. When the pin is low, initialization of the chip is executed.
10 D/C# Data/Command Control
This pin is Data/Command control pin..
When the pin is pulled high and serial interface mode is selected, the data at SDIN is treated as data. When it is pulled low, the data at SDIN will be transferred to the command register. In I2C mode, this pin acts as SA0 for slave address selection.
11 SCLK When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK.
12 SDIN
13 IREF Current Reference for Brightness Adjustment
This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 12.5μA.
14 VCOMH Voltage Output High Level for COM Signal
This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS.
15 VCC Power Supply for OEL Panel
This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used.

Spécifications générales

Article Dimensions Unité
Matrice de points (Résolution) 128 × 32 points
Dimensions du module 30.0 × 11.5 × 1.26 mm
Zone active 22.384 × 5.584 mm
Taille des points 0.152 × 0.152 mm
Pas des points 0.175 × 0.175 mm
Mode d'affichage Matrice passive
Couleur d'affichage Monochrome
Drive Duty 1/32 Duty
IC SSD1306BZ
Interface 4-wire SPI
Diagonale 0.91 pouces

Valeurs nominales maximales absolues

Parameter Symbole Valeur min Valeur max Unité
Supply Voltage for Logic VDD 0 4.0 V
Supply Voltage for Display VCC 0 16.0 V
Température de fonctionnement TOP -40 +80 °C
Température de stockage TSTG -40 +85 °C

Caractéristiques électroniques

DC Caractéristiques électroniques

Article Symbole État Valeur min Valeur type Valeur max Unité
Supply Voltage for Logic VDD 2.8 3.0 3.3 V
Supply Voltage for Display VCC 7 7.25 8 V
Input High Volt. VIH 0.8×VDD VDDIO V
Input Low Volt. VIL 0 0.2×VDD V
Output High Volt. VOH 0.9×VDD VDDIO V
Output Low Volt. VOL 0 0.1×VDD V
Operating Current for VCC (VCC Supplied Externally) ICC Vcc =7.25V 7 11 mA


Search keyword: 128x32 oled, oled 128x32, 0.91 oled, 0.91" oled, 0.91 pouces oled, oled 0.91, oled 0.91"
go top
close