Accueil Produits Afficheur TFT Module LCD TFT standard WF24LTYAJDNN0

N° de modèle WF24LTYAJDNN0

►Dimension: 2.4 pouces
►Résolution d’écran: 240 x 320 points
►Vue préférentielle 6h
►Interface: MCU, SPI
►Contrôleur intégré: ILI9341V
►Carte de contrôle : NON
►Luminosité (Cd/m²): 500
►Holding frame with fixing points: NON
►Dalle tactile: NON

DESSIN

2.4" IPS Color TFT Module - WF24LTYAJDNN0 - Winstar Display

SPÉCIFICATIONS

Fonction PIN sur l'interface

NO Symbole Fonction I/O
1 GND Ground P
2-6 NC No connection -
7 VCI High voltage power supply for analog circuit blocks
(2.5 ~ 3.3 V)
P
8 IOVCC Low voltage power supply for interface logic circuits
(1.65 ~ 3.3 V)
P
9 TE Tearing effect output pin to synchronize MPU to frame writing, activated by S/W command. When this pin is not activated, this pin is low.
If not used, open this pin.
O
10 CS Chip select signal. I
11 D/CX(SCL) (D/CX): This pin is used to select “Data or Command” in the parallel interface.
When DCX = 1, data is selected.
When DCX = 0, command is selected.
(SCL): This pin is used as the serial interface clock in 3-wire 9-bit/4-wire 8-bit serial data interface.
If not used, this pin should be connected to VDDI or VSS.
I
12 WR(SPI_D/C) (WRX) - 8080-Ⅰ/8080-Ⅱ system: Serves as a write signal and writes data at the rising edge.
(D/CX) - 4-line system: Serves as the selector of command or parameter.
Fix to VDDI level when not in use.
I
13 RD 8080-Ⅰ/8080-Ⅱ system (RDX): Serves as a read signal and MCU read data at the rising edge.
Fix to VDDI level when not in use.
I
14-29 DB0~DB15 18-bit parallel bi-directional data bus for MCU system and RGB interface mode Fix to VSS level when not in use. I/O
30 RESET This signal will reset the device and must be applied to properly initialize the chip.
Signal is active low.
I
31 IM0 Select the MCU interface mode

MPU Parallel interface bus and serial interface select
If use RGB Interface must select serial interface.
* : Fix this pin at VDDI or VSS.
I
32 IM1
33 IM2
34 DB16 18-bit parallel bi-directional data bus for MCU system and RGB interface mode Fix to VSS level when not in use. I/O
35 DB17
36 LEDK Cathode of LED backlight. P
37 LEDK Cathode of LED backlight. P
38 LEDA Anode of LED backlight. P
39 SDI(SDA) When IM[3] : Low, Serial in/out signal.
When IM[3] : High, Serial input signal.
The data is applied on the rising edge of the SCL signal.
If not used, fix this pin at VDDI or VSS.
I/O
40 SDO Serial output signal.
The data is outputted on the falling edge of the SCL signal.
If not used, open this pin
O

Spécifications générales

Article Dimensions Unité
Diagonale 2.4 pouces
Matrice de points (Résolution) 240 × RGB × 320(TFT) points
Dimensions du module 42.72(W) × 60.26(H) × 2.8(D) mm
Zone active 36.72 × 48.96 mm
Pas des points 0.153 × 0.153 mm
Type de LCD TFT, Noir, Transmissif
Contrôleur IC ILI9341V or equivalent
Vue préférentielle 80/80/80/80
Rapport d'aspect Portrait
Type de rétroéclairage LED, Blanc
Dalle tactile Sans dalle tactile
Surface Reflets

Valeurs nominales maximales absolues

Article Symbole Valeur min Valeur type Valeur max Unité
Température de fonctionnement TOP -20 +70
Température de stockage TST -30 +80

Caractéristiques électroniques

Article Symbole Valeur min Valeur type Valeur max Unité
Supply Voltage For Analog VCI 2.5 3.3 V
Supply Voltage For Logic IOVCC 2.5 3.3 V
Supply Current For LCM ICI 6 9 mA
go top
close