제품 OLED 디스플레이 그래픽 OLED 디스플레이 WEO012832F

I2C, 0.91인치 OLED 디스플레이 패널

모델 번호 WEO012832F

►Thinner version OLED
►유형 : 그래픽
►구조 : COG
►크기 : 0.91 인치
►128x32 점 행렬
►내장형 컨트롤러 SSD1306BZ
►3V 전원 공급 장치
►1/32 duty
►인터페이스 : I2C

설명

  • WEO012832FWPP3N00001 : 백색
  • WEO012832FLPP3N00001 : 노란색

도면

Winstar 0.91,OLED I2C, OLED I2C Display - WEO012832F

사양

인터페이스 핀 기능

No. 기호 기능
1 C2P Positive Terminal of the Flying Inverting CapacitorNegative Terminal of the Flying Boost CapacitorThe charge-pump capacitors are required between the terminals. They must be floated when the converter is not used.
2 C2N
3 C1P
4 C1N
5 VBAT Power Supply for DC/DC Converter Circuit
This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used.
6 NC No connection
7 VSS Ground of Logic Circuit
This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground.
8 VDD Power Supply for Logic
This is a voltage supply pin. It must be connected to external source.
9 RES# Power Reset for Controller and Driver
This pin is reset signal input. When the pin is low, initialization of the chip is executed.
10 SCL I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin inapplication and D0 is the serial clock input, SCL.
11 SDA
12 IREF Current Reference for Brightness Adjustment
This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 12.5μA.
13 VCOMH Voltage Output High Level for COM Signal
This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS.
14 VCC Power Supply for OEL Panel
This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used.

일반 사양

항목 치수 단위
도트 매트릭스 (해상도) 128 × 32
모듈 치수 30.0 × 11.5 × 1.26 mm
활성 영역 22.384 × 5.584 mm
도트 크기 0.152 × 0.152 mm
도트 피치 0.175 × 0.175 mm
디스플레이 모드 패시브 매트릭스
디스플레이 색상 Monochrome
Drive Duty 1/32 Duty
IC SSD1306BZ
인터페이스 I2C
크기 (대각선) 0.91 인치

절대 최대 정격값

Parameter 기호 최소값 최대값 단위
Supply Voltage for Logic VDD 0 4.0 V
Supply Voltage for Display VCC 0 16.0 V
작동 온도 TOP -40 +80 °C
보관 온도 TSTG -40 +85 °C

전기적 특성

DC 전기적 특성

항목 기호 조건 최소값 대표값 최대값 단위
Supply Voltage for Logic VDD 2.8 3.0 3.3 V
Supply Voltage for Display VCC 7 7.25 8 V
Input High Volt. VIH 0.8×VDD VDDIO V
Input Low Volt. VIL 0 0.2×VDD V
Output High Volt. VOH 0.9×VDD VDDIO V
Output Low Volt. VOL 0 0.1×VDD V
Operating Current for VCC (VCC Supplied Externally) ICC Vcc =7.25V 7 11 mA


Search keyword: 128x32 oled, oled 128x32, 0.91 oled, 0.91" oled, 0.91 인치 oled, oled 0.91, oled 0.91"
go top
close