제품 OLED 디스플레이 그래픽 OLED 디스플레이 WEO012864Q

2.7", 128x64 그래픽 OLED 디스플레이 모듈

모델 번호 WEO012864Q

►유형 : 그래픽(프레임 없이)
►구조 : COG
►크기 : 2.7 인치
►128 x 64 점 행렬
►내장형 컨트롤러 SSD1309ZC
►3V 전원 공급 장치
►1/64 duty
►인터페이스 : 6800, 8080, SPI, I2C

설명

  • WEO012864QW : 백색
  • WEO012864QL : 노란색
  • WEO012864QS : 하늘색

도면

Winstar Display - 2.7", 128x64, Monochrome Graphic OLED Display

사양

인터페이스 핀 기능

No. Symbol Function
1 NC  No connection
2 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
3 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
4 IREF This pin is the segment output current reference pin. IREF is supplied externally.
5~12 D7~D0 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout,
SDAin in application and D0 is the serial clock input, SCL.
13 E/RD# This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
14 R/W# This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
15 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
When 3-wire serial interface is selected, this pin must be connected to VSS.
16 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
17 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
18 NC No connection
19 BS2 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2, BS1 and BS0 are pin select

Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD
20 BS1
21 VDD Power supply pin for core logic operation
22~28 NC No connection
29 VSS Ground.
30 NC No connection

기계적 데이터

항목 치수 단위
도트 매트릭스 128 × 64
모듈 치수 73.0 × 41.86 × 2.05 mm
활성 영역 61.41 × 30.69 mm
도트 크기 0.45 × 0.45 mm
도트 피치 0.48 × 0.48 mm
디스플레이 모드 패시브 매트릭스 (Passive Matrix)
디스플레이 색 Monochrome
Drive Duty 1/64 Duty

전기적 특성

항목 기호 조건 최소값 대표값 최대값 단위
Supply Voltage for Logic VDD 2.8 3.0 3.3 V
Supply Voltage for Display VCC 12.5 13 13.5 V
High Level Input VIH 0.8×VDD V
Low Level Input VIL 0.2×VDD V
High Level Output VOH 0.9×VDD V
Low Level Output VOL 0.1×VDD V
50% Check Board operating Current VCC =13.0V 20 22 24 mA

Search keyword: 128x64 oled, oled 128x64, 2.7 oled, 2.7 inch oled, oled 2.7
go top
close