제품 TFT LCD 표준 TFT LCD 모듈 WF24LTYAJDNN0

2.4 인치 IPS TFT LCD 모듈

모델 번호 WF24LTYAJDNN0

►크기 : 2.4 인치
►디스플레이 형식 : 240 x 320 dots
►뷰 방향 : IPS
►인터페이스 : MCU, SPI
►내장형 컨트롤러: ILI9341V
►제어 보드 : 없음
►밝기(cd/m²): 500
►스루 홀 프레임 : 없음
►터치스크린 : 없음

도면

2.4" IPS Color TFT Module - WF24LTYAJDNN0 - Winstar Display

사양

인터페이스 핀 기능

NO 기호 기능 I/O
1 GND Ground P
2-6 NC No connection -
7 VCI High voltage power supply for analog circuit blocks
(2.5 ~ 3.3 V)
P
8 IOVCC Low voltage power supply for interface logic circuits
(1.65 ~ 3.3 V)
P
9 TE Tearing effect output pin to synchronize MPU to frame writing, activated by S/W command. When this pin is not activated, this pin is low.
If not used, open this pin.
O
10 CS Chip select signal. I
11 D/CX(SCL) (D/CX): This pin is used to select “Data or Command” in the parallel interface.
When DCX = 1, data is selected.
When DCX = 0, command is selected.
(SCL): This pin is used as the serial interface clock in 3-wire 9-bit/4-wire 8-bit serial data interface.
If not used, this pin should be connected to VDDI or VSS.
I
12 WR(SPI_D/C) (WRX) - 8080-Ⅰ/8080-Ⅱ system: Serves as a write signal and writes data at the rising edge.
(D/CX) - 4-line system: Serves as the selector of command or parameter.
Fix to VDDI level when not in use.
I
13 RD 8080-Ⅰ/8080-Ⅱ system (RDX): Serves as a read signal and MCU read data at the rising edge.
Fix to VDDI level when not in use.
I
14-29 DB0~DB15 18-bit parallel bi-directional data bus for MCU system and RGB interface mode Fix to VSS level when not in use. I/O
30 RESET This signal will reset the device and must be applied to properly initialize the chip.
Signal is active low.
I
31 IM0 Select the MCU interface mode

MPU Parallel interface bus and serial interface select
If use RGB Interface must select serial interface.
* : Fix this pin at VDDI or VSS.
I
32 IM1
33 IM2
34 DB16 18-bit parallel bi-directional data bus for MCU system and RGB interface mode Fix to VSS level when not in use. I/O
35 DB17
36 LEDK Cathode of LED backlight. P
37 LEDK Cathode of LED backlight. P
38 LEDA Anode of LED backlight. P
39 SDI(SDA) When IM[3] : Low, Serial in/out signal.
When IM[3] : High, Serial input signal.
The data is applied on the rising edge of the SCL signal.
If not used, fix this pin at VDDI or VSS.
I/O
40 SDO Serial output signal.
The data is outputted on the falling edge of the SCL signal.
If not used, open this pin
O

일반 사양

항목 치수 단위
크기 (대각선) 2.4 인치
도트 매트릭스 (해상도) 240 × RGB × 320(TFT) dots
모듈 치수 42.72(W) × 60.26(H) × 2.8(D) mm
활성 영역 36.72 × 48.96 mm
도트 피치 0.153 × 0.153 mm
LCD 유형 TFT, 검은색, 투과성
제어 IC ILI9341V 또는 이와 동등한
시야각 80/80/80/80
종횡비 Portrait
역광 타입 LED,백색
터치 패널 터치패널(스크린)이 없는
표면 눈부심

절대 최대 정격값

항목 기호 최소값 대표값 최대값 단위
작동 온도 TOP -20 +70
보관 온도 TST -30 +80

전기적 특성

항목 기호 최소값 대표값 최대값 단위
Supply Voltage For Analog VCI 2.5 3.3 V
Supply Voltage For Logic IOVCC 2.5 3.3 V
Supply Current For LCM ICI 6 9 mA
go top
close