Home Products OLED Module Graphic OLED Display WEO006432A

0.49" Micro OLED Display 64x32

Model No. WEO006432A

►Type: Graphic
►Structure: COG
►0.49" Micro OLED Display
►64x32 Dot Matrix
►Built-in controller SSD1306BZ
►3V Power supply
►1/32 duty
►Interface: I2C
►Suitable for Wearable Device
►OLED Micro Display / Micro Display

DESCRIPTION

Winstar OLED WEO006432A is a 0.49 inch passive matrix Micro OLED Display Module which is made of 64x32 dots. The WEO006432A has the module dimension of 14.5x 11.6 x 1.26 mm and Active Area size 11.18 × 5.58 mm. WEO006432A Micro Display is built in with SSD1306BZ IC, it supports I2C interface, 3V power supply. The WEO006432A is a COG structure OLED display which is ultra thin and no need of backlight (self emitting); it’s lightweight and low power consumption. This 0.49 inch small sized OLED module is suitable for wearable device, mp3, portable device, personal care appliance, voice recorder pen, health device, etc. 

The standard emitting colors for this item are available in white and sky blue. WEO006432A module can be operating at temperatures from -40℃ to +80℃; its storage temperatures range from -40℃ to +85℃.

  • WEO006432AL : Yellow
  • WEO006432AS : Sky Blue
  • WEO006432AW : White

     

DRAWING

Micro OLED Display, Micro Display, OLED Micro Display,0.49 OELD, 64x32 OLED - Winstar

SPECIFICATIONS

Interface Pin Function

No. Symbol Function
1 C2N Positive Terminal of the Flying Inverting Capacitor Negative Terminal of the Flying Boost Capacitor The charge-pump capacitors are required between the terminals. They must be floated when the converter is not used.
2 C2P
3 C1P
4 C1N
5 VBAT Power Supply for DC/DC Converter Circuit
This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used.
6 NC No connection.
7 VSS Ground of Logic Circuit
This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground.
8 VDD Power Supply for Logic
This is a voltage supply pin. It must be connected to external source.
9 RES# Power Reset for Controller and Driver
This pin is reset signal input. When the pin is low, initialization of the chip is executed.
10 SCL Host Data Input/Output Bus
11 SDA When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. When I2C mode is selected, D2 & D1 should be tired together and serve as SDAout & SDAin in application and D0 is the serial clock input SCL.
12 IREF Current Reference for Brightness Adjustment
This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 12.5μA.
13 VCOMH Voltage Output High Level for COM Signal
This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS.
14 VCC Power Supply for OEL Panel
This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used.

Mechanical Data

Item Dimension Unit
Dot Matrix 64 × 32 Dots
Module dimension 14.5 × 11.6 × 1.26 mm
Active Area 11.18 × 5.58 mm
Pixel Size 0.153 × 0.153 mm
Pixel Pitch 0.175 × 0.175 mm
Display Mode Passive Matrix
Display Color Sky Blue / White
Drive Duty 1/32 Duty
IC SSD1306BZ

Electronical Characteristics

Item Symbol Condition Min Typ Max Unit
Supply Voltage for Logic  VDD 2.8 3 3.3 V
Supply Voltage for Display  VCC 7 7.5 7.8 V
Input High Volt. VIH 0.8×VDD VDDIO V
Input Low Volt. VIL 0 0.2×VDD V
Output High Volt. VOH 0.9×VDD VDDIO V
Output Low Volt. VOL 0 0.1×VDD V
50% Check Board operating Current ICC VCC=7.5V 5 20 mA

Search keyword: 64x32 oled, oled 64x32,0.49 oled, 0.49" oled, 0.49 inch oled, oled 0.49, oled 0.49"
go top
close