На главную страницу Продукция OLED Дисплей Графический OLED дисплей WEO012864L-Hotbar

SH1106 OLED модуль,1.28", 128x64 (Hot bar FPC)

№ модели WEO012864L-Hotbar

►Тип: Графический(Без рамки)
►Тип монтажа контроллера: COG + Hot bar FPC
►Диагональ: 1.28 дюйма
►Разрешение: 128 x 64 точек
►3V power supply
►1/64 duty cycle
►Интерфейс: 6800 / 8080 / 3-SPI /4-SPI / I2C
►Встроенный контроллер: SH1106G

Описание

  • WEO012864LWPP3N00000 : белый
  • WEO012864LLPP3N00000 : Желтый
  • WEO012864LSAP3N00000 : Небесно голубойv

DRAWING

Winstar 1.28" SH1106 OLED Display Module 128x64 - WEO012864L-Hotbar

Техническое описание

Функции контроллера контактного интерфейса

No. Символы Описание
1 NC(GND) No connection
2 C1N Connect to charge pump capacitor.
These pins are not used and should be disconnected when Vpp is supplied externally.
3 C1P
4 C2P Connect to charge pump capacitor.
These pins are not used and should be disconnected when Vpp is supplied externally.
5 C2N
6 VDD2 3.0 – 4.7V power supply pad for Power supply for charge pump circuit.
This pin should be disconnected when VPP is supplied externally
7 NC No connection
8 VSS Ground.
9 VDD1 Power supply input: 1.65 - 3.5V
10 IM0 These are the MPU interface mode select pads.
  8080 I2C 6800 4-wire SPI 3-wire SPI
IM0 0 0 0 0 1
IM1 1 1 0 0 0
IM2 1 0 1 0 0
11 IM1
12 IM2
13 CSB This pad is the chip select input. When CSB = “L”, then the chip select becomes active, and data/command I/O is enabled.
14 RESB This is a reset signal input pad. When RES is set to “L”, the settings are initialized. The reset operation is performed by the RES signal level.
15 A0 This is the Data/Command control pad that determines whether the data bits are data or a command.
A0 = “H”: the inputs at D0 to D7 are treated as display data.
A0 = “L”: the inputs at D0 to D7 are transferred to the command registers.
In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver.
16 WRB This is a MPU interface input pad.
When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU WR signal. The signals on the data bus are latched at the rising edge of the WR signal.
When connected to a 6800 Series MPU: This is the read/write control signal input terminal.
When R/W = “H”: Read.
When R/W = “L”: Write.
17 RDB This is a MPU interface input pad.
When connected to an 8080 series MPU, it is active LOW. This pad is connected to the RD signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”.
When connected to a 6800 series MPU , this is active HIGH. This is used as an enable clock input of the 6800 series MPU.
When RD = “H”: Enable.
When RD = “L”: Disable.
18 D0 This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance.
When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDAI). At this time, D2 to D7 are set to high impedance.
19 D1
20 D2
21 D3
22 D4
23 D5
24 D6
25 D7
26 IREF This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 18.75uA.
27 VCOMH This is a pad for the voltage output high level for common signals.
A capacitor should be connected between this pad and VSS.
28 VPP OLED panel power supply. Generated by internal charge pump.
Connect to capacitor. It could be supplied externally.
29 VSL This is a segment voltage reference pad.
This pad should be connected to VSS externally.
30 NC(GND) No connection

Механические характеристики

Наименование Измерения Единица
Разрешение 128 x 64
Габариты 34.50 × 23.00 × 1.65 mm
Активная область 29.42 × 14.20 mm
Размер пикселя 0.205 × 0.197 mm
Шаг пикселя 0.230 × 0.222 mm
Матрица Пассивная
Цвет дисплея монохромные, Белый / Желтый / Небесно голубой
Рабочий цикл 1/64 Duty
IC-Контроллер SH1106G
Интерфейс 6800/8080/3-SPI /4-SPI / I2C
Диагональ 1.28 дюйма

Абсолютные максимальные значения

Параметр Символы Минимальный Максимальный Единица
Напряжение питания логических схем VDD1 -0.3 3.6 V
Power supply for charge pump circuit VDD2 -0.3 4.8 V
Напряжение питания дисплея VPP -0.3 14.5 V
Диапазон рабочих температур TOP -40 +80 °C
Температура хранения TSTG -40 +85 °C

Электронные характеристики

DC Электронные характеристики

Наименование Символы Кондиция Минимальный Типичный Максимальный Единица
Напряжение питания логических схем VDD1 2.8 3.0 3.3 V
Напряжение питания дисплея VPP 6.75 7.25 7.75 V
Вход высокого уровня VIH 0.8xVDD1 VDD1 V
Вход низкого уровня VIL VSS 0.2xVDD1 V
Выход высокого уровня VOH 0.8xVDD1 VDD1 V
Выход низкого уровня VOL VSS 0.2xVDD1 V
50% Check Board operating Current VPP =7.25V 5.0 6.0 7.0 mA
 

Search keyword: 128x64 oled, oled 128x64, 1.28 oled, 1.28" oled, 1.28 дюйма oled, oled 1.28, oled 1.28"

go top
close