首頁 產品介紹 OLED顯示器 繪圖型 OLED 顯示器 WEO009664B-ZIF

1.1吋 96x64 OLED面板 - ZIF

型號 WEO009664B-ZIF

►類型: 繪圖型
►結構: COG + ZIF FPC
►1.1吋OLED
►96 x 64 點陣
►內建控制器 SSD1327
►3V電源電壓
►1/64 duty
►介面: 6800, 8080, SPI, I2C
►穿戴式電子產品適用

產品敘述

WEO009664B是一款1.1吋的PM OLED顯示器模組,解析度96x64 pixels, 帶ZIF FPC。此款模組內建SSD1327 IC,模組操作支援 6800/8080 8-bit 平行介面,I2C與4-線SPI介面,3V電壓驅動,1/64 duty與支援16灰階。此款1.1” COG結構 WEO009664B模組可視為2017年EOL的TAB結構 1.1" WEX009664A/B的替代方案選項,兩者的AA區尺寸接近都是1.1吋薄型OLED模組。

1.1" 的WEO009664B是小尺寸COG結構的OLED,無需背光非常輕薄 ,非常適用於攜帶式裝置、智慧醫療產品、個人健康守護追蹤裝置、量測儀器,智能家電、穿戴式裝置等產品。此模組的工作溫度是-40℃至+80℃,儲存溫度-40℃至+85℃。

  • WEO009664BL : 黃色

 

規格圖

Small OLED Screen, OLED Display Screen, 1.1 OLED Screen Module - WEO009664B

產品規格

Pin功能定義

No. 符號 說明
1 VSS Ground pin. It must be connected to external ground.
2 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
3 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS. No external power supply is allowed to connect to this pin.
4 VCI Low voltage power supply and power supply for interface logic level. It should match with the MCU interface voltage level and must be connected to external source.
VCI must always set to be equivalent to or higher than VDD.
5 VDD Power supply pin for core logic operation.
6 BS1 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2, BS1 and BS0 are pin select.
Bus Interface selection
 
BS[2:1] Interface
0 4 line SPI
1 I2C
11 8-bit 8080 parallel
10 8-bit 6800 parallel

Note  (1) 0 is connected to VSS  (2) 1 is connected to VCI
7 BS2
8 VSS Ground pin. It must be connected to external ground.
9 IREF This pin is the segment output current reference pin
10 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
11 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
12 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
When 3-wire serial interface is selected, this pin must be connected to VSS.
13 R/W# This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
14 E This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
15 D0 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
16 D1
17 D2
18 D3
19 D4
20 D5
21 D6
22 D7
23 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
24 VSS Ground pin.

規格說明

項目 尺寸 單位
解析度 96 × 64 Dots
模組尺寸 29.00 × 22.50 × 1.65 mm
檢視區域 22.53 × 15.01 mm
像素大小 0.205 × 0.205 mm
像素間距 0.235 × 0.235 mm
顯示模式 被動矩陣
顯示顏色 單色
驅動方式 1/64 Duty
IC SSD1327
介面 4-Wire SPI, I2C, 6800, 8080
尺寸 1.1吋

電氣特性

項目 符號 條件 最小值 典型值 最大值 單位
邏輯電源電壓 VCI 2.8 3.0 3.3 V
顯示電源電壓 VCC 8.0 8.5 9.0 V
輸入高電壓 VIH 0.8×VCI VCI V
輸入低電壓 VIL VSS 0.2×VCI V
輸出高電壓 VOH 0.9×VCI VCI V
輸低高電壓 VOL VSS 0.1×VCI V
50% Check Board operating Current ICC VCC=8.5V 13.0 26.0 mA

最大絕對額定值

參數 符號 最小值 最大值 單位
工作電源電壓 VCI -0.3 4.0 V
邏輯電源電壓 VDD -0.5 2.75 V
顯示電源電壓 VCC -0.5 19.0 V
工作溫度 TOP -40 +80 °C
儲存溫度 TSTG -40 +85 °C

Search keyword: 96x64 oled, oled 96x64, 1.1 oled, 1.1" oled, 1.1吋 oled, oled 1.1, oled 1.1"
go top
close